1. ASTM electrical standard is a absolute system.

2. An American Society for Testing and Materials (ASTM) label.

3. Sixblocks were made according to American ASTM Standard.

4. Sample size for testing shall be based upon ASTM F1470 Sample level A, acceptance number in all cases is zero defect.

5. All field splices were bolted using ASTM A 325 hex head bolts.

6. Stems shall be of dezincification-resistant silicon bronze ASTM B 371 or low-zinc alloy B 99, non-asbestos packing and malleable or ductile iron handwheel.

7. Certificate: En 71, ASTM D, Low lead, Low Cadmium, Phthalate free.

8. ASTM D1159-01 Standard Test Method for Bromine Numbers of Petroleum Distillates and Commercial Aliphatic Olefins by Electrometric Titration.

9. The material quality is ASTM A 743 M ( ZG 00 Cr 13 Ni 4 Mo ) the austenite stainless steel.

9. is a sentence dictionary, on which you can find excellent sentences for a large number of words.

10. It raises an objection against ASTM D 4172 precision value and equipment requirement, and adopts an attitude of negating to constantly import four-ball wear tester.

11. ASTM E 648: Stard test method for critical radiant flux of floor-covering systems using a radiant heat energy source.

12. Stems shall be of dezincification-resistant silicon bronze ASTM B 371 or low-zinc alloy B 99 non-asbestos packing and malleable or ductile iron handwheel. Valve ends may be threaded or solder type.

13. Typical composition, ASTM Standard does not specify materials to this detail.

14. Sample size for testing shall be based upon ASTM F1470 Sample Level A, acceptance number in all cases is zero defects.

15. ASTM D2710-99 Standard Test Method for Bromine Index of Petroleum Hydrocarbons by Electrometric Titration.

16. The United States in 1982 issued a "concrete and mortar used for grinding blast furnace slag fine-grained" standard (ASTM C989 - 82), and was revised in 1989.

17. The ASTM standard method D 2500 - 66 for cloud point measurement covers transparent petroleum products.

18. The ASTM data was treated to produce the TBP data and the mean average boiling point by explicit correlations and then the pseudo-components were cut by using the integral method.

19. ASTM C 1166: Standard test method for flame propagation of dense and cellular elastomeric gaskets and accessories.

20. In ASTM D244, the density cup is a stainless steel measurer of known standard volume(), but the shape and the dimension was not presented.

21. The electrodes follow the ASTM Standard D 257 entitled " DC Resistance or Conductance of Insulating Materials. "

22. Further information on four - point probe measurements can be found in the ASTM standard F 84.

23. Standards most frequently referenced in plastic piping specifications are ASTM Standards.

24. The standard covers dimensions and gaging of plastic tapered National Pipe Threads (NPT) for leak-tight joints, and it is now referenced in all ASTM Standards for plastic piping products.

25. Valve Body, Cover, Tailpiece and Control Stop shall be in conformance with ASTM Alloy Classification for Semi-Red Brass.

26. This independent third party certifier provides assurance that products and materials are regularly tested to comply with ASTM and ANSI Standards.

27. FCC feedstocks and equilibrium catalysts from 10 refineries are analysed and evaluated by the conventional ASTM/GB or RIPP standard analysis procedures.

28. EPA Federal Reference Method 24 specifies the use of ASTM D 2369 - 93.

29. The submersible motor enclosure including frame, end brackets, flanges and cap assembly shall be constructed of close-grained cast iron, ASTM A-48, Class 30 or better.

30. The pump casing, impeller, motor housing and stationary base elbow shall be manufactured of close-grained cast iron, ASTM A48, Class 30.

31. The dry-pit submersible motor enclosure including frame, end brackets, flanges and cap assembly shall be constructed of close-grained cast iron, ASTM A-48, Class 30 or better.

32. ASTM E 648:Standard test method for critical radiant flux of floor-covering systems using a radiant heat energy source.

33. ASTM D2896-03 Standard Test Method for Base Number of Petroleum Products by Potentiometric Perchloric Acid Titration.

34. In this paper, a set of important formulae for burnup determination of fuel element from HFETR are deduced and researched, and main formulae of ASTM E244 are reformed.

35. The Classic Style Durometers from PTC Instruments are built to meet or exceed current ASTM D2240, and ISO 868 specifications and are the most popular durometer sold today.

36. The most frequently referenced industry standards for plastic piping systems are ASTM Standard Specifications and Practices.