1 She felt she was snubbed here.

2 She snubbed him by ignoring his question.

3 He took the opportunity to deliver us another snub.

4 She was repeatedly snubbed by her neighbours.

5 I think she felt snubbed because Anthony hadn't bothered to introduce himself.

6 His cancellation of the concert was seen as a deliberate snub to the organizers.

7 He snubbed her in public and made her feel an idiot.

8 She snubbed them by not replying to their invitation.

9 Eisenhower saw the action as a deliberate snub.

10 The revelry was snubbed by my father.

11 All the country's leading players snubbed the tournament.

12 I tried to be friendly, but she snubbed me completely.

13 The German move was widely seen as a deliberate snub to Mr Cook.

14 I tried to make a suggestion but she snubbed me.

15 I simply didn't recognize her and apparently she took it as a snub.

16 He was not invited to the party, and felt snubbed.

17 Her refusal to attend the dinner is being seen as a deliberate snub to the President.

18 His application was snubbed.

19 In the office, we avenge slight slights with small snubs.

20 The world is full of people looking for spectacular happiness while they snub contentment. Doug Larson 

21 Snubber circuit of switching power supply.

22 Mathematical analysis, Pspice simulation and experimental results snubber scheme.

23 The clamping snubber circuit was set to the rated breakdown voltage of the MOSFET (600 V and 800 V respectively).

24 This paper introduces the experimental results of two snubber circuits for the full bridge switch circuit constituted by MOSFETs in case of the inductive load and large current operation.

25 This paper presents a novel passive snubber circuit suitable for inverter bridge leg modules.

26 At last, an parameter design of RC snubber for thyristors in a engineering project is presented.

27 The operation mode of the circuit is analyzed and the condition of how to achieve soft switch is discussed, how to design the parameters of the snubber is presented as well.

28 At last, we show the effectiveness and the applicability of the improved snubber circuit through theoretical analysis and circuit simulation.

29 The experimental(results) show that the EMI level of the integrated motor system has an obvious attenuation after adding snubber and filter.

30 Once the source is identified, the RF energy may be reduced or eliminated by shielding and adding snubber networks or filters at appropriate points.

31 The parameters of the model were provided for an IGBT of FF300R12ME3 as an example. The model was used in analysis of switching characteristics, snubber circuit, and paralleled operation of the IGBT.

32 This snubber could obviously snub the harmonics in the output waveform which would appear when the switching devices are shifted from on to off.

33 Having much less turn-off time, eliminating the current over-shot and improving the turn-off consistency, the proposed snubber is suitable as the load energy snubber of TEM transmitter.

34 Firstly, the summarize of the development and actuality of flyback converter is given, and different snubber circuits applied in the flyback converter are analyzed and compared.

35 It can also be used for passive lossless snubber in PFC.

36 Figure 44 shows the same OUTPUT response with the snubber in place.

37 The voltage overshoot across the power electronics and the voltage variation could be suppressed by snubber.

38 A simplified method using transfer matrix method was applied to the analysis and calculation of the vibration damping effect induced by dry friction snubber on the blade platform.

39 The model for general snubber circuits is presented by means of analyzing the snubber circuit of a chopper.

40 This paper puts forward a soft switching circuit of snubber type with a mutual inductance. The analysis result and parameter design method of the circuit are given .

41 In addition,(http:///snubber.html) the appropriate parameters of snubber circuits and dead-times for IGBT were worked out.

42 The piston rod of family sedan's rear snubber fractured duringearlier stage of rotary bending fatigue test.