1 Adopting seperate - combined oil pump, maintenance easy.

2 How about the operation condition of jacking oil pump?

3 Starting Motor, Oil Pump Electrical Motor, Armature.

4 Activates the auxiliary oil pump.

5 The main factors affecting the rotor oil pump′s volume efficiency have been analyzed theoretically, and the leaky mechanism of the rotor oil pump′s gap is discussed.

6 Description : Zhejiang Pingchai Pumps ---- Oil pump , tappet valve guide, rod.

7 If the compressor, the oil pump and corresponding reverse back, so lubrication oil pump will not work, compressor lubrication will occur, thus make compressor obstacles can't work normally.

8 The high pressure oil pump has stable performance, easy starting and operation reliability.

9 The daily is used up, the oil pump should be clean, clear the fear of copper wire cloth oil dirties.

10 Combined oil pump, power source of the machine, provides working fluid with certain pressure.

11 External components for the oil pump pressure lubrication oil lubrication system of forced circulation type.

12 Exyernal motor oil pump enable good ventilating and cooling conditions, safety operation and prolonged service life.

13 With the RHD oil pump controller coordination use, may realize the self-lubrication and the malfunction alert.

14 When this new-type oil pump will be put into production has been specified by the manager.

15 The steel pipe at oil pump outlet used connector with cutting ring, avoid the possibility of hose bust-up under high working pressure.

16 After the oil pump motor finishes starting, the pump is loaded.

17 Detailed introduction of high pressure oil pump for mixer modified with PLC control.

18 The position of the lube oil pump is not suitable.

19 Lubrification degradation of low sulfur diesel oil causes oil pump abrasion of engine.

20 Inside the transmission, an electric oil pump replaces the torque - converter pump.

21 Oil pump speed regulation technology and the general principle for speed regulator slection are intro - duced.

22 Our company mainly product oil pump, valve guide, valve Tappet, push rod and so on.

23 External catalyst cooler is located between hot oil pump room, regenerator and catalyst tank, very difficult to be hoisted.

24 The transferability of the yawp of the pressing operation oil pump in the sample can express the physical condition change.

25 Water pump housing, Hubs, Bearing housing, Dampers hub oil ring, sector shaft, oil pump cover, water in let and outlet, vacuum pump .

26 Application: Main shaft of airplane engine or machine tool, high frequency motor, air compressor, oil pump and so on.

27 Main products: oil tank, oil tube , oiler support , oil pump, oil applying wheel etc.

28 The paper analyses the reasons of oil vapor produced in the light oil pump house. Some measures that should be taken to reduce oil vapor are introduced.

29 The tests of main transformer cooling configuration on its blast furnace and oil pump are the key fac-tor of all measurements.

30 Operation test of emergency switching - off device for oil pump and ventilator ( bilge pump ) in engine room.

31 The case of recoiler is used as an oil tank, on which the lubrication oil pump is mounted for circulating lubrication.

32 The influencing factors of the return force of 165MN oil pump direct-drive free forging press have been analysed and the design principle of the press's return force given.

33 Light oil pump house is mainly used to convey some volatile and inflammable oil products.

34 To provide incineration line and auxiliary fuel under low caloric value of wastes, the whole plant will set up a centralized oil depot and oil pump room.

35 The oil filter pump , to plug into the pipeline or oil viscosity too high, can be caused by the oil pump into the mouth through the high vacuum Department so that the air infiltration.

36 The paper describes a sudden shutdown of the air separation plant operating in Nylon 66 Salt Corporation due to instantaneous power failure of the compressor oil pump.

37 Our company processes pottery microsection, excircle polishing of porcelain tube, engineering plastics, automobile oil pump sealing element, etc...

38 Use the example of coordinating light oil pump house and fire system transformation to discuss the design problem of oil house transformation with modern safety conception.

39 The brake oil pump is communicated with a hydraulic braking clamp through a high pressure pipe,[http:///oil pump.html] and the hydraulic braking clamp is engaged with the brake disk.

40 Pumping truck is a truck which is mounted in power takeoff, oil pump, speeder and so on to transfer oil for the army.

41 Stop the running of one oil pump of the electric motor.

42 The electricity consumption of oil pump of hydraulic pressure system accounts for 80% of that of the whole plastic injection molding machine, so it is crucial to lower the electricity consumption.

43 We professionally manufacture the testing equipment of oil pump and nozzle.

44 A thermohard steel was investigated based on applied condition of the hot oil pump.

45 First of all, compressor lubrication oil pump is usually composed of spindle drive of the compressor.

46 I plant in Qingxian Story, is a professional production of non - self - lubricating oil pump professional manufacturers.

47 As a result, oil pump frictional losses are reduced during the warm - up period.