1. Turn the sliding contact of the potentiometer to approximately mid-position.

2. Turn the sliding contact of the potentiometer to approximately mid-position. Connect the battery.

3. The 1M potentiometer should be prepared by attaching short wires to the centre and one of its outer terminals.

4. Don't blindly turn this potentiometer.

4. is a online sentence dictionary, on which you can find nice sentences for a large number of words.

5. Digital potentiometer sensitivity adjustment and breakage location.

6. In electronics, the moveable arm of a potentiometer.

7. Lead in Trimmer Potentiometer elements.

8. Lead in cermet - based trimmer potentiometer elements.

9. The technique character of the potentiometer cover was introduced.

10. A servo potentiometer that generates the signal for comparison with the input signal.

11. The wiper of the potentiometer is connected directly to the spindle.

12. Nut is widely used in electronic components, potentiometer, quartz core machine, lamp and so on.

13. Potentiometer should not be wiry, but it is desirable to coal or multiturn .

14. The digital potentiometer's bandwidth determines the maximum data rate for signals transmitted through the potentiometer.

15. In this paper , the autocontrol to Potentiometer Drill machine by industrial computers will be achieved.

16. In the contemporary acoustic equipment, usually uses the potentiometer to carry on the volume control.

17. Nonpolarized capacitor C1 and potentiometer R2, a linear taper, determine the time constant of integrator IC1B.

18. As the computer technologies are applied widely, the potentiometer is used for the characteristic measurement of H.

19. The potentiometer is set up so that it gives a positive voltage when the missile accelerates and a negative voltage when it decelerates .

20. The three terminals of the potentiometer are available for use as either a variable resistor or a resistor divider.

21. You can program the digital potentiometer through its serial interface during board or system test.

22. Take OMRON CPM1A as an example, the changing setting value methods in which we use analog input potentiometer, dial switch and push-switch are introduced.

23. The threshold value signal of two-valued is offered by Digital potentiometer which is controlled by SCM.

24. Being a linear output indicator completed with precision multi-turn wirewound potentiometer.

25. Hardware design includes circuits of signal amplification of digital potentiometer, analog switch, A/D conversion, wave conversion, single-chip and peripheral equipment.

26. Principle of high voltage power supply based on PWM chip TL494 is introduced in this paper. The adjustment of the voltage is performed by digital potentiometer controlled by MCU.

27. It also introduces a method according to the actual situation to put a fixed resistance combination of potentiometer, and it improved the accuracy of circuit.

28. This paper analysed the uncertainties of voltmeter in calibration by potentiometer.

29. The major way to improve the linear precision of Rotary Synthetic Carbon Film Potentiometer is to trim resistance using the advanced equipments.

30. The temperature sensors, start switch S1, and current control potentiometer are all connected to the board using servo lead wire (available at many hobby shops in 10 foot lengths).

31. Can also ask the glass glaze of design precise and trimming according to user, potentiometer.

32. The principle and circuit of monitoring system in laser welding are introduced in this article, which consist of numeric control potentiometer, instrumentation amplifier and SCP for data processing.

33. A potentiometer measured the position of the tip during the penetration.

34. Select a nonvolatile digital potentiometer if you must program the gate's state in nonvolatile memory.

35. Rotate the potentiometer P 7 completely clockwise, P 2 and P 4 completely counter clockwise.

36. Avoid drawing any current from the wiper of a potentiometer.

37. The controller can be driven in local mode by a potentiometer.

38. Button control digital potentiometer X9511 is consists of time delay circuit removed dithering, mono- stability circuit, preventative dithering trigger.

39. Sliding resistance was replaced by the fixed value resistance, and potentiometer was used to adjust volt, it could make measurement of diode reverse characteristic more convenient.

40. Linear potentiometer can reach 0.01mm high accuracy, and all position settings can be saved into the computer, suitable for high precision molding.

41. Electric analog switch is adopted to replace the commonly used mechanical potentiometer switch and a series of antidisturbance way is used, which improves the reliability of the diagnostic results.

42. A method of determining alkalinity and sodium hydrosulfite content in indigo solution, using potentiometer, is reported.

43. An input device that provides a scalar value , e . g . , a thumb wheel, a potentiometer.

44. The moving vane type airflowing sensor consists of air flowmeter and potentiometer.

45. Wiring is simple, just to the three-terminal potentiometer received at the converter input voltage, output voltage and the public side can be.

46. The supply electricity using permanent current source for the DC potentiometer can simplify working processes and raise working efficiency.

47. Asynchronization mechanism in duplex potentiometer and simple,[] active count measures to improve its synchronism are described.

48. The electrolytic level is therefore electrically equivalent to a potentiometer, the center electrode corresponding to the rotor arm.