1. It is particularly useful for interlaboratory quality control programs.

2. A stepping motor control program flowchart is shown in Fig. 6.11.

3. In any case, an irresponsible control program has been set in motion without sufficient information as to its future effects.

4. Standard on Fire Department Infection Control Program.

5. The main control program is made by VC.

6. How is the population control program in China?

7. The system firmware program consists of the single-chip control program, the interrupt program and USB communication program, etc.

8. Second, the system application programs including main control program, user operation interface program, keyboard program and S3C44B0X related function module driving program are described.

9. The wind way system, water way system, PLC control program and the communication with computer are present in detail.

10. The human-computer interface and the monitoring and control program are developed.

11. The Beijing - Tianjin sandstorm - control program has treated 900,000 hectares of land.

12. Based on the characteristics of numerical control program and compiler, a means was presented for the structure and design of NC code translator module and the implement technology was described.

13. That part of a control program that is resident in main storage.

14. A rapid increase in population would be a natural corollary of any such changes in the birth control program.

15. Although the new practices elevated patient morale, they had little effect on the overall structure of the leprosy control program.

16. The different characteristics between S/R instruction and Step Ladder instruction (STL) for designing sequential control program of PLC are putted forward passing through...

17. The different characteristics between S/R instruction and Step Ladder instruction (STL) for designing sequential control program of PLC are putted forward passing through comparison.

18. Image forming equipment, control method, computer readable recording media of storage control program.

19. As for code-treatment and interpolation functions, modules for code translation, linear and circular interpolation were developed for the numerical control program.

20. This paper introduces two typical design methods of sequential control program, which based on living example of F1 PLC from MITSUBISH.

21. In this paper, on the basis of our predecessors, I proposed separately by electro-optic modulator automatic gain control and automatic bias control program.

22. This paper introduces the required basic functions of intermittent gas making furnace control program and points to be alert.

22. try its best to gather and build good sentences.

23. The hardware circuit of control system and the flowchart of main control program for software were designed by using PIC single chip (microprocessor).

24. The numerical control machine is controlled by the numerical control program, and a series of special CNC instruction code Constitute the numerical control program.

25. The paper described the collectivity function characteristic and several important components of movement controller, for example main control program, interpolation module and velocity control.

26. It includes examination-adjustment program, failure process program, display program, information management program, I/O control program and data transform program.

27. The paper analyzes the advantages to adopt PLC in automatic control system of pump house, and gives automatic control block diagram and control program flowsheet block diagram.

28. The configuration of control loops, control methods in every stage and master control program are described.

29. Secret data storage device, secret data reading method, and control program storing medium.

30. All you need to do is to edit style control program, you can get bright and colorful towel , Turkish towel , decorating cloth, etc.

31. In dynamic library mode, atomic processing module is loaded dynamically in logic control program.

32. By analyzing the anti-surge control system on ITCC, the anti-surge control theory, control mode, control program and the method of surge check program is introduced.

33. All solder powders that are used for our paste manufacturing are made under inert atmosphere and under tight quality control program.

34. The node from which an NCP ( network control program ) command is issued.

35. After the primary scheme being made up, the appropriate wireless communication mode and developing tool of master control program has also been selected.

36. The application program area is employed by the system programmer for implementing the control program.

37. By analysing the anti-surge control system on ITCC , the artical introduces the anti-surge control theory, control mode, control program and method of surge check program.

38. The function of the control program, stored in the 4 K EPROM already, has eight kinds of capability.

39. Previously operating system was not included in embedded system, and the simple cycle control program mainly dealt with request from exterior.

40. Wireless base station, network system, communication method, and base station control program.

41. The advantage function in PLC is stepping sequence control, the efficiency method of establishment the stepping sequence control program is drawing out the function diagram.

42. This text draws the schematic circuit diagram of operating logic control system, and attaches basic operation control program under this working model.

43. The main control program in software design was provided, which can control the speed and turning of the step motor.

44. According to the processing ask characteristic of workpiece, with stepping sequence control and master control program, make the 3 kinds of control way of machine tool facilitate realization.

45. The main control program, other application modules and characteristic library of currency recognition are transplanted from old system .

46. Still, UNFPA leaders claim they have no knowledge of or involvement in the population control program.

47. The if - else statement is probably the most basic way to control program flow.

48. The different characteristics between S/R instruction and Step Ladder instruction (STL) for designing sequential control program of PLC are ...

49. To Embed the control program debugged successfully into EPROM and debug the system on EPROM.

50. The control program includes timing interrupt service program, external interrupt service program and main program.

51. On the physical hardware, a control program can be the host operating system or a hypervisor (see Figure 1).

52. And the main control program of the multi-frame system isdescribed in this paper.

52. try its best to gather and make good sentences.

53. To Supervise the Group's Financial Report Mechanism and Internal Control Program.

54. Conclusion The master control program has the features of user interface simply regulation.

55. Operating system is the main control program of a computer that schedules tasks, manages storage, and handles communication with peripherals.

56. Design method and basic principle for ABB elevator master control program is analysed taking Fanshan phosphate Mine auxiliary shaft elevator as an example.

57. And system power conversion unit status job simulation, effective system control program to verify the effectiveness and feasibility.

58. Relevant persons have studied the revised Incoming Inspection Spec. and the File Control Program.

59. Complished the hardware design, this paper presents the software design including control program, modified time slot generating program and friendly upper-computer manager program.

60. Methods OPC technology was used. A temperature supervisor control program and a database application were designed by VB, and the temperature was control by the fuzzy control methods.

61. Taking the hydraulic rotating table as example, the design methods of sequential control program using FX2N PLC from Mitsubishi, the application features of every method by comparison were presented.

62. Chapter 6 describes the drive software of data acquisition and control board. It discusses the design of self checking program, data acquisition and control program, data read and processing program.

63. The main chip of the control box is 89C52. The main control program is made by VC.

64. The management representative organizes relevant persons to study the revised Incoming Inspection Spec. and the File Control Program.

65. Linear functions of the PI regulator output and the trigger angle simplify the control program and make the excitation current follow the set current quickly.

66. Final section reveals the risks of financial innovation in risk control program.

67. That which running daily in a refinery belongs to the procession of continuous production. Its job control program should be listed in the flow control model.