1. The full supply voltage is applied to the winding and the current is rapidly boosted to slightly above rated.

2. The current is now opposed by the supply voltage and is rapidly forced to zero.

3. A large supply voltage and phase resistance are only required when the motor is operating at high speeds.

4. How can the supply voltage and consequently the phase current - be increased during acceleration or deceleration?

5. Built - in amplifier, supply voltage DC 12 to 24 V. To Contol output directly.

5. is a sentence dictionary, on which you can find excellent sentences for a large number of words.

6. The low supply current and the low supply voltage makes these parts ideal for battery - powered applications.

7. Note: Special requirement on the supply voltage may be noted when ordering.

8. The power supply voltage line includes an edge part formed in an obtuse angle .

9. Voltage sag is that the root-mean-square value of supply voltage drops suddenly inthe short time.

10. It depends on the tube type, the power supply voltage, the reflected impedance, and the required operating point.

11. Rated voltage of the electromagnetic brake is 205V(DC). Supply voltage of the rectifier si 220v(AC).

12. The equipment used in supply voltage must be the product of the supply voltage line nameplate.

13. About the supply voltage, frequency, capacity factor of the fan and motor, specification of coil pipe, kinds of humidifier, form and efficiency of air filter, caliber and direction of pipe and etc.

14. This paper introduces a supply voltage band - gap reference circuit which used a self - bias cascode current mirror.

15. The first pull-up resistance unit supplies a supply voltage to the first node, thereby determining an initial pull-up code or a voltage level on the first node.

16. Voltage regulation is not required for IC2 either because its timing is largely independent of the supply voltage.

17. On test with no load the divider chip consumed only 19mA at a supply voltage of 1.8V.

18. During these freewheeling intervals the effective phase voltage is equal to the d.c. supply voltage.

19. The clocking circuit configured to provide the pull-up current to an internal node in response to a clock signal having the input supply voltage and the ground voltage.

20. The design of negative sequence protection is mainly introduced with seriously unbalanced power supply voltage fault, open phase fault and two-phase short circuit fault.

21. Features: Low VCE ( sat ) , High performance at low supply voltage.

22. At the same instant, Q3 sources current into R4 through D1, thereby pulling the voltage on R4 to a diode drop below the supply voltage.

23. During signal conditions, the output swings above and below the supply voltage.

24. The output characteristics also make the AD590 easy to multiplex: the current can be switched by a CMOS multiplexer or the supply voltage can be switched by a logic gate output.

25. Attention shall be paid to whether the rated value of local supply voltage is accordant to that of "XINYAN" charger or not during traveling.

26. Change over from normal to emergency mode shall occur at not less than 0.6 times rated supply voltage, It shall not occur at greater than 0.85 times rated supply voltage.

27. Three-phase isolation transformer has been widely used in AC 50-60HZ 500V three-phase power supply voltage does not exceed the occasion.

28. The generator may be made independent of temperature and supply voltage if the detector is clamped with matched zener diodes as shown in Figure 28.

29. New FET-input amplifiers, like the AD820 family of amplifiers, incorporate design improvements that prevent output voltage phase reversal for signals within the rated supply voltage range.

30. Therefore, how to improve power quality and to provide a stable supply voltage become more important.

31. During normal operation the memory elements may be powered with a power supply voltage that is larger than the programmable core logic power supply voltage.

32. Reference source outputs a stable reference signal which is independent of power supply voltage, temperature and process.

33. The filament current and x-ray power supply voltage are checked before the exposure signal can be transmitted.

34. Accordingly, raising percent of pass power supply voltage is the main task of power supply enterprise.

35. The load current is calculated from the supply voltage and the load power ( or resistance ).

35. try its best to gather and make good sentences.

36. This paper presents a novel current source which is insensitive to supply voltage.

37. As another example, the logic state of the select signal can be changed in response to a change in the power supply voltage provided to the phase frequency detector.

38. Voltage generated by the motor at the instant of reclose may be equal to the supply voltage but exactly out of phase.

39. The characteristics of nonlinear amplifier change with temperature and supply voltage. In order to ensure stability of amplifier, the adaptive predistortion becomes very important.

40. Simulation results indicate that V 2 control responses quickly to supply voltage change and load change.

41. The power consumption is 34 mW and supply voltage is 1.8 V.

42. If the efficiency of servo amplifier is considered, it is practicable that the power supply voltage is about 3 times as large as the servo amplifier output voltage corresponding to rated current.

43. If the project parts list does not specify a voltage, choose a capacitor with a rating which is greater than the project's power supply voltage.

44. The filament current and x - ray supply voltage are checked before the exposure signal can be transmitted.

45. Check that the voltage plate on the motor is suitable for the supply voltage available.

46. The paper derives out the proper power supply voltage of city road lighting according to the illuminance and life span character at different voltage level.

47. A supply voltage can be supplied at the primary winding and the transformer provides a current and a voltage at the secondary windings.

48. The reset unit is used for determining whether to generate a reset signal according to the level of the power supply voltage when receiving the first voltage from the over-temperature protection unit.

49. It also must be large enough to withstand the supply voltage.

50. The switching circuit determines whether to apply the power supply voltage to a chip in response to the control signal.

51. However if the supply voltage or ambient temperature is low the machine still reduces input power at this preset time.

52. During data loading operations, the memory elements may be powered with a power supply voltage equal to the programmable core logic power supply voltage.

53. Don't forget that the actual plate voltage swings both above and below the supply voltage, and the center of the swing is the actual plate supply voltage.

54. Some parameters affecting the frequency and magnitude of power supply, such as supply voltage, duty of control sigal. the R and C of oscillation circuit are discussed.

55. A supply voltage monitor and protection circuit is presented, and its theory of operation is analyzed.

56. Like the transformer coupled circuit, the choke feed in the parafeed circuit allows the output to swing above and below the power supply voltage.

57. The reference voltage, VREF, is applied externally and can be set up to the supply voltage, VDD.

58. An approach for designing analog current - mode circuits with very - low supply voltage requirements is described.

59. The gain of the PMT, that is the ratio of anode output current to the photoelectric current from the photocathode, is directly related to the supply voltage.

60. A low supply voltage sample-and-hold circuit for a pipelined analog-to-digital converter is described .

61. Supply voltage must be broken in the operating voltage range of 220 V.

62. The designed converter could operate well with a slender supply voltage signal because of its high input resistance and low offset drift.

63. The emitter follower is capable of eliminating the adverse effects of load caused by the zero sequence component of the supply voltage.

64. Pay - Direct - cycloconverter supply voltage AC motor in accordance with the different control methods are divided into voltage-and current-mode two.