(1) When using both ohmic contacts or an ohmic contact and a contact limited contact, the EL efficiency is determined by injection at lower voltages and recombination at higher voltages.

(2) Due to the ohmic resistance in the conductor some energy were lost in transmission.

(3) The effect of ohmic dissipation on the evolution and saturation of this turbulence is investigated.

(4) Introduce the principle of ohmic heating technology and it's system application in food disinfection.

(5) Insulation Resistance . The ohmic resistance of insulation. It degrades quickly as humidity increases.

(6) It can be concluded that the ohmic potential drop is an important factor which has the influence over the pit growth kinetics.

(7) Products: Low ohmic precision and power resistors, SMD and conventional technology.

(8) The capability of the ohmic contact electrodes was tested through the I-V curve.

(9) A relation between an increase in the ohmic resistance and the ohmic restriction resistance of a conducting plate with a sharply changing width is shown.

(10) Ohmic heating has many advantages in contrast to traditional heating.

(11) The principle[/ohmic.html], operation and development of ohmic heating sterilization technology were reviewed.

(12) The films have Ohmic contact property, whose resistance is increasing with the increase of Ag doping concentration, which matches the model of Maxwell's theory of effective media.

(13) The Methods: Which comparing the ohmic heating sterilization with the water bathe heating were taken.

(14) Noise due to antenna ohmic loss is important in ultralow noise system.

(15) A material obeying ohm's law is called an ohmic conductor or a linear conductor.

(16) The characteristics of starch solution ohmic heating were also investigated.

(17) Very high ohmic value resistors may exhibit a significant change in resistance with a change in applied voltage.

(18) The ohmic resistance and the charge transfer resistance of the battery are increased with the increasing of delivered capacity.

(19) The development of the food ohmic heating technology and its future trend were predicted.

(20) The pit growth law has been derived in consideration of the ohmic potential drop inside a pit.

(21) The active layer is made on high N type doping layer, and has a less area than ohmic contact layer.

(22) It has been shown that all three tests have caused the ohmic contact resistance to increase at the end of the tests, which leads to the failure of the contact.

(23) The dynamics of entanglement decoherence for fragile entangled states is discussed by taking into account the ohmic dissipation under the low temperature approximation.

(24) By chemical deposition process, nickel electrode on PTCR ceramics of ohmic contact can be acquired at low cost.

(25) The EIS results show that the dominant loss of the SOFC is from the ohmic resistance of the electrolyte.

(26) Aerospace series - Cables, electrical, aircraft use - Test methods - Ohmic resistance per unit length.

(27) There is no prominent change of gelatinization properties during ohmic heating.

(28) Problems in measurement of water level(or liquid level)in deep wells are solved through developing the intelligence water level gauge instead of Ohmic method.

(29) The geometry of the cell cavity was carefully designed to minimize the ohmic potential drop and edge effect.

(30) The test shall be carried out at the power output of the apparatus corresponding to 10% overvoltage with any declared minustolerance on the ohmic resistance.

(31) In this paper, a simple method to measure the specific contact resistance of metal-semiconductor ohmic contact is developed, using the probe heads of the inline four probes.

(32) Ohmic heating technology is a new kind of food technic whit many merits and large development.

(33) With MOSFETS soft-switched, the switching power loss of MOSFETS, the ohmic loss and the iron loss of coupler core was reduced. It had large importance to improve the whole efficiency for the system.

(34) Ohmic contact is a critical factor for high power semiconductor lasers.

(35) However, it also increases both the ohmic loss at the solid-state electrolyte and the polarization loss at both electrodes.

(36) The method can be used for forming a metal-semiconductor schottky junction and forming ohmic contact between the metal and the semiconductor on the high-doped semiconductor.

(37) The back ohmic contact resistance of Al-BSF by DC magnetron sputtering is downtrend with the annealing temperature increasing, and less than that by the screen printing process.