1. The camshaft rotates in phase with the crankshaft, but at half its speed.

2. Mods include sportier camshafts and bigger valves.

3. His design does away with the latter's camshafts and valves.

4. The manganate phosphating technology of camshaft is introduced.

5. This is called an overhead camshaft arrangement.

6. Since 1958, an engine with a single overhead camshaft has been used.

7. The isothermal quenching process of the ductile iron camshaft was analyzed.

8. Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.

9. The sedan camshafts re-melting and chilling process and production technique of shell mold camshaft castings to he re-melted and chilled were introduced.

10. Upward camshaft; chain transmission; timing distribution system is stable and has little noise.

11. In case that the camshaft signal measured by the first falling edge after dentation is low( ), then the following TDC would be of the first cylinder.

12. To disclose the reasons of hot-tearing of camshaft produced by bottom gating system and vertical casting process, the temperature-field of the camshaft under the above technique conditions was tested.

13. The camshaft has a cam, on which there is a lob , or bump.

14. As the camshaft continues to rotate, the high spot moves way from the valve mechanism.

15. The sedan camshafts re-melting and chilling process and production technique of shell mold camshaft castings to be re-melted and chilled were introduced.

16. A youngish man deals with us, taking us to the shop floor where camshafts are made.

17. The compression figures, whilst not particularly low, suggest that it may be camshaft wear.

18. Ivars needs help with a Hobson or a Zenith carburettor, correct camshaft timing and much more.

19. This paper studies concept, calculation and gauge design concerned with coaxality of main spindle hole and camshaft hole and points out some common errors.

20. A high pressurized design method of slipper pairs of a new type camshaft connecting-rod low speed high torque motor was put forward.

21. The software mainly processes the rotate speed signal of the crankshaft and camshaft position signal to export ignition control signal.

22. Insert a self - tapping screw into the drilled pin and carefully pull the pin from the camshaft.

23. The effect of pouring temperature on the microstructure of chilled iron camshaft was studied.

24. In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.

25. This paper describes the design method of the swinging master as the attachment in a camshaft copying lathe.

26. The practical production has verified that the overmeasure of camshaft workpieces has been well distributed and met the working requirements when the cam masters designed in this way have been used.

27. Since the engine has no valves, it doesn't need any camshaft, valve lifters and so on.

28. Electromagnetic control valve actuation is a new kind of variable valve timing technology. It can offer more advantages than general camshaft valve actuation when used in the engine.

29. Properly inoculant amount was used to reduce the chill depth of the cam during the production of chilled iron camshaft.

30. This device is particularly suited to those applications that require extremely accurate duty cycle control or accurate edge-detection, such as automotive camshaft sensing.

1. The camshaft rotates in phase with the crankshaft, but at half its speed.

31. The value - opening mechanism includes a valve lifter and a cam on a camshaft.

32. In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.

33. The opening of each valve is controlled by a camshaft.

34. These engines are known as dual overhead camshaft ( DOHC ) engines.

35. A dynamics model for valve gear of overhead camshaft engine is presented in this paper.

36. Chilled cast iron camshaft has less production procedure and energy consumption and lower costs.

37. The production process of chilled cast iron camshaft made by Citroen Automobile Co. was introduced. The comparison between domestic and foreign camshaft production status was made.

38. Argon arc remelting hardening is a new technology of manufacturing camshaft.

39. The influence of inoculant addition amount on the structure and properties of camshaft was investigated.

40. The camshaft and crankshaft gears can be connected directly, or meshed.

41. This article analyzes the defect of the camshaft quenching machine, brings forward the effective design plan.

42. Angular velocity grinding and linear velocity grinding are the main grinding method for camshaft.

43. The camshaft position sensor is located in the distributor on all engines.

44. The MLX90217 is a self adjusting digital output rotary position gear tooth sensor designed for use in automotive camshaft sensing as well as other speed sensing applications.

45. As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.

46. If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets .

46.

47. Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.

48. A new method is proposed to determine the excited torque and bearing load of the injection pump camshaft by means of measuring the longitudinal strain in the bottom part of the plunger.

49. Molded part 2 by elbow Festival, the camshaft or put pressure on double-toggle System.

50. Camshaft out of time.

51. The main products are as follows, exhaust manifold, bent axle, camshaft, rubbing sassafras nestification, gearbox, support, flywheel, etc.

52. A sort of chilled nodular iron camshaft was developed by adopting resin - coated sand shell casting process.

53. Abstrct:It has been introduced that structural character, main parameters and design and manufacture of shell molding camshaft die.