1. Does not bid good-bye forever, our hand connecting rod walks together.

2. The connecting rod is made from forged alloy steel.

3. Install connecting rod bolt protectors on rod bolts.

3. is a sentence dictionary, on which you can find good sentences for a large number of words.

4. The piston pin joins the piston to connecting rod.

5. The connecting rod may drive a valve stem directly.

6. Fabric: unique crank and connecting rod structure, mandatory under the feeding device, completely solved the problem shaped brick cloth, the second fabric can produce a variety of colored road brick.

7. Taking for example the wear of connecting rod copper sleeve, the paper introduces the application of this method to the prediction of internal combustion engine maintenance and fault detection.

8. The connecting rod carries the power thrusts from the piston to the crankpin .

9. The chemical composition, microstructure and mechanical properties of connecting rod blank made of microalloy steel are analyzed.

10. The reliability of main bearing and connecting rod large end bearing for 12V240ZJ diesel engine whose power has been increased up to the E type grade was analyzed.

11. The improvement of heat treatment process of the connecting rod hot forging dies was introduced.

12. Connecting rod is mainly bearing alternate loads such as compression, stretch, bending and otherwise.

13. The influence of large radial deformation of connecting rod bearing bore's surface on lubrication analysis of connecting rod bearing should be considered.

14. The lower end of the connecting rod fits the crankshaft journal.

15. The strength analysis for a articulated connecting rod has been investigated in this paper.

16. The connecting rod links its large end to the crankshaft and its small end to the piston.

17. NEW Elastic Walking Mechanism ( NEWM ) Spring connecting rod mechanism applied on quadruped walking robot was introduced.

18. Double oil cylinder and precise four-column automatic balance connecting rod structure, which can guarantee the absolutely same cutting depth of each cutting position.

19. Connecting rod is one of the most important parts in a locomotive engine.

20. A piston links to a drive shaft by means of a connecting rod.

21. Case research proved it's effective to recognize new data of fault model and diagnose the faults of connecting rod bearing .

22. The result has shown that the fracture was caused by such surface defects as fold crack in section A at connecting rod small end.

23. This paper points out one kind of new type four - connecting rod self - locking hoist.

24. The FEM for the assembly parts of piston, gudgeon pin and small-end of connecting rod is constructed to investigate a diesel engine piston with an oscillating-oil-cooling channel.

25. General steps of tolerance analysis and tolerance optimization were provided. To verify the effectiveness of the approach, connecting rod structure and piston structure in diesel engine were tested.

26. This link may be broken by the jagged up, "Huff" as to ensure the absolute accuracy of the fastening position, thereby reducing friction and extending connecting rod life.

27. A beam that connects the piston rod to the connecting rod of a reciprocating engine.

28. Disclosed is a timing device for opening coal stove door, comprising a furnace door wind screen (5) and a connecting rod raising mechanism.

29. Warm compaction technology have been successfully employed to automotive parts including turbine hub, connecting rod, gears, whole coil and electronic igniter, and so on.

30. Based on the working feature of flying shear mechanisms and considering the motion track, velocity and position angle of connecting rod, a multi-objective optimization model is built.

1. A piston links to a drive shaft by means of a connecting rod.

31. When you and she window-shop, she can be very happy, when your connecting rod enters haunted house time, she can have one kind of security sense ...

32. The piston is connected to the crank shaft by a connecting rod.

33. The paper mainly discusses the processing techniques of connecting rod and its jig design.

33. try its best to gather and make good sentences.

34. The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.

35. The connecting rod is attached to the piston by the piston pin.

36. Kalman filtering is also helpful in the connecting rod splitting detection system developed in this research.

37. By connecting rod by gas turbocharger with small area of gas piston driven directly connected large reciprocating air piston.

38. An operator presses the handle, which acts on sternums by the connecting rod and the sternum massager, and hearts are pressed. Blood in the hearts and aortas is compelled to flow and circulate.

39. The crank end of the connecting rod is sometimes called the rod " big end ".

40. A new method based on the wavelet packet and fuzzy C-clusters about connecting rod bearing fault was put forward.

41. Connecting rod feeding mechanism , needle bar basting, looper hooking form parallel chain - stitch, which stitch is firmelastic.

42. The crank and connecting rod mechanism (CCRM) is often used in automatization machineries. It can transform circumrotation movement into to-and-fro beeline movement.

43. In using the model DC6105 diesel engine, connecting rod cracks and its small end bushing breakdown are occasionally happened.

44. The rod - bearing cap attaches the connecting rod to the crankpin.

45. Can connecting rod time, please only do not be side - by - side.

46. This design instruction booklet carries on the explanation in view of the connecting rod reducing socket double face milling aggregate machine-tool design and the unit clamp design.

47. Germany is one of the first draw on the balance connecting rod structure which developed sophisticated self-balancing four-post Hydraulic Cutting Machine businesses.

48. I steam operating company, Moldova accessories, connecting rod , crankshaft, gears, ball, forging tools.

49. Product features: inseparable. Door switch buckle mechanism for easy and quick installation of connecting rod.

50. In traditional design, there is no quantitative analysis on the elastohydrodynamic lubrication for engine's connecting rod bearing.

51. The piston pin joins the piston to the connecting rod.

52. The connecting rod carries the power thrusts from the piston to the crankpin. At the same time, the rod is in eccentric motion.

53. The double-track type external fixed bracket mainly comprises a power connecting rod with threads, a sliding connecting rod without threads, 4-6 sliding bodies and an ear-shaped body.

54. Secondly, the kinematics equations of Rocker Arm Module are derived according to simplifying the robot's rocker arms as open chain mechanisms of space connecting rod.

55. The connecting rod is attached to the crankshaft at one end (big end) and to the piston at the other end (small end).

56. Taking the simplified directionless graphed model of piston connecting rod set as a base, and the detachability calculation was analyzed when the piston connecting rod set were all being disassembled.

57. It is quite correct in measuring the bending strength of connecting rod journal fillet of most normal structure crankshafts, but for some special structure crankshaft, it can't obtain ideal results.

58. With the connecting rod formed three very linkage of isolating switch.

59. By the bucket wheel loader working device, connecting rod, rocker arm, turn fights, cylinder and lifting cylinder.

60. The cathode is hung on an anode bar, and a cathode bar is arranged on a nylon pulley and driven by a motor and a crank connecting rod to do reciprocating translational motion.

61. The connecting rod links its large end to the crankshaft and its small end piston.

62. I hoped we can the connecting rod walk continuously, until forever!

63. It was good except that the connecting rod for the letter x was gone.

64. The flapping mechanism adopts a parallel quadrilateral connecting rod mechanism to lead the tail fin of the robotic fish arranged on a tail fin frame to make periodic translational motion.

65. The result indicates the material not only meets need of connecting rod but also has low ductile fracture and good fracture joggle in definite condition.

66. By making a force triangle, the force in the connecting rod can be determined.