1) Electric rays stun their prey with huge electrical discharges.

2) Tiny electrical discharges zipped and buzzed about the hull as the fragile air was catalysed around them.

3) A novel micro electrical discharge machining(EDM) method is described.

4) The power generator gave off an electrical discharge.

5) Comparative experiments between powder - mixed electrical discharge machining ( EDM ) and conventional EDM are carried out.

6) Both forms are readily gasified by electrical discharge without leaving any tangible residue.

7) In order to eliminate higher harmonics embedded driving signal in miniaturized EDM(Electrical Discharge Machining) system, matching circuit for ultrasonic generator has been carried out.

8) The core technique problems during wire cut electrical discharge machining in the inner conductor sheet were analyzed by this paper.

9) It is well known that an electrical discharge through a gas causes it to glow. When electricity flows through neon gas you see a beautiful orange-red light.

10) There is machining error in electrical discharge machining ( EDM ) due to the electrode's orbiting.

11) Due to a little quantity, electrical discharge machining(Micro-EDM) is usually developed in single production, leading to long production cycle, repetitive design and high cost.

12) The newest trends of electrical discharge machining(EDM) including die-sinking EDM, micro EDM and wire EDM(WEDM) in Japan were presented.

13) The rules that the spindle servo system parameters would influence the workability of mixed air EDM (electrical discharge machining) technology are introduced.

14) Micro electrical discharge machining (MWEDM), a nontraditional micro gear die fabrication method, is presented in this paper.

15) Electrical discharge machining (EDM), or spark machining, as it is so called, is based on the eroding effect of an electric spark on both the electrodes used to produce.

16) When applying the electrical discharge machining process, the material is eroded as a result of electrical discharge between tool and work.

17) The Electrical Discharge Machining (EDM) has been a very important method of machining, and performs its alternative function in industry.

18) Electrical discharge machining removes metal by controlled electrical arcing ( sparking ) between the tool and workpiece.

19) Ultrasonic vibration electrical discharge machining ( UEDM ) in gas is proposed in this paper.

20) Franklin's experiments showed that the lightning is an electrical discharge.

21) As an important part of WEDM (Wire Cut Electrical Discharge Machining) machine , pulse generator is one of main factors which influence WEDM process.

22) A new WEDM(Wire Electrical Discharge Machining) technology for finishing cut has been developed, in which gas has been used as a dielectric instead of water.

23) The deep rumbling beneath their feet abruptly stopped, and the electrical discharges faded away.

24) The technical officer could not fail to be conscious of the lethal potential of an electrical discharge from the platform.

25) Ultraviolet radiation could do the same job as the electrical discharge in their laboratory.

26) Such gases, mixed with water vapour, were subjected to electrical discharge and ultraviolet light.

27) Such a source is provided by any atomic vapour in which an electrical discharge is running.

28) The stainless steel fibrous porous materials are processed by Wire cut Electrical Discharge Machining(WEDM).

29) Abstract: The paper deals with a linear direct drive mechanism of electrode for electrical discharge machining(EDM) and its drive and control principle.

30) In standard conditions,[http:///electrical discharge.html] the effects of suspended activated carbon particles in gas-liquid series electrical discharge reactor were evaluated for the degradation of organic contaminants.

31) The article analyzes the characteristic and the working condition of the cutting fluid using in electrical discharge machining (EDM).

32) The accurate analysis method of performances plays an important role in the optimization with multiple performance objectives of micro electrical discharge machining(EDM).

33) ScienceDaily (Apr. 13, 2010) — In focal epilepsy, seizures are generated by a localized, synchronous neuronal electrical discharge that may spread to large portions of the brain.

34) The concept, characteristics and application of high energy beam machining, electrical discharge machining, electrochemical machining and material abscission machining separately discuss.

35) The plasma oscillation spectrum of electrical discharge channel is analyzed, and the eigenfrequency of metal crystal lattice vibration is discovered in the spectrum.

36) The damaged layer of monocrystalline silicon cut by wire electrical discharge machining (WEDM) was investigated via cross-section microscopy and preferred etching detection methods.

37) Comparative measurements of percentage of silicon on the surface of workpiece by powder-mixed electrical discharge machining (EDM) were carried out.

38) The advantage is that electrical discharge machining processes with good surface roughness and machines metal of any hardness.