1. The steam turbine is less economical at cruising speed.

2. In a steam turbine, the steam pushes against blades.

3. General Arrangement Steam Turbine Train.

4. As an important parameter of steam turbine governing system, the dead band property was generally taken from the static characteristic curve.

5. Disposal of salt scaling in a back-pressure steam turbine by supersaturated steam method is described with respects to the procedure and points for attention.

6. Steam turbine valve management is one of the important functions of digital electro - hydraulic ( DEH ) control system.

6. Wish you will love and make progress everyday!

7. Notes: 1. Type of steam turbine: B - Backpressure turbine, C - Extraction condensation turbine.

8. The TG 70 steam turbine has a operation speed of 9600 rotations per minute ( RPM ) .

9. Steam turbine is a main component of thermal power plant, and its vane is lifeline.

10. Main equipment including: boiler, steam turbine, generator complete and their auxiliary equipments.

11. The boiler, the steam turbine and the pump work in rated capacity, thus all getting the highest electric generation efficiency.

12. Based on the analysis of steam turbine components and its flow network, a modularized simulation component library was created, which contains typical units and basic elements of steam turbines.

13. For low cycle fatigue life of steam turbine components with normal or a logarithmic normal distribution, a calculation method of the safe life expectation is given together with a practical example.

14. An expert system for steam turbine cold-state start-up at Baicheng Power Plant has been designed through the use of expert system development tool.

15. Then they boasted about technological innovations - steam engines, railway locomotives, steam turbines and so on.

16. With the fast development of the construction in pithead power plant, the large air cooling steam turbine has been widely used in China.

17. An analytical recurrence method was developed for calculating the thermal stresses in steam turbine rotor with a central hole.

18. A method and system for determining a limit exceedance of an operating parameter in a steam turbine system.

19. This paper presents a method for creep life calculation of steam turbine parts.

20. The jam fault of the differentiator is dangerous to steam turbine.

21. Vacuum condenser is applicable to condensing exhaust steam from steam turbine.

22. The technique of simulation has been proved a good way in studying dynamic characteristics or improving control system of steam turbine.

23. Sean Riley puts on his hazmat suit and heads into the radiation zone for his next tough fix, replacing a steam turbine in a nuclear power plant to boost its energy-producing capacity.

24. Turbine's Low pressure Exhaust Hood ( TLEH ) is an important unit of steam turbine.

25. The forms, features, causes and countermeasures of the faults for condensing system of a marine steam turbine geared unit are introduced.

26. This paper mainly discusses the off - design traits for the last stage of condensed steam turbine.

27. The ideal cycle heat efficiency used nowadays is affected by the relative internal efficiency so it can't reflect the operation economic state of thermal system of steam turbine.

28. The technique proved effective when it was used in rapid crack testing and crack depth measuring of steam turbine metal parts such as joint face of hig.

29. The variation of circulating water flow directly affects the vacuum of condenser efficiency of steam turbine.

30. In the variable conditions calculation of thermodynamic calculation for marine steam turbine, it is often for overcritical conditions and overflow conditions to occur.

31. Firstly, two defining methods of relative internal efficiency for steam turbine are analyzed from energy equilibrium.

32. Steam turbine, generator rotor journal wear and tear, strain of the electro - brush plating, thermal spray repair.

33. Steam turbine casing collision test is used to determine the minimum through-flow clearance between rotor and assembled casing parts.

34. The way of supplying heat with low vacuum of small-middle steam turbine can save energy sources, but it will have effect on safety of steam turbine itself.

35. This paper presents the vibration analysis and treatment of No. 2 bearing of the steam turbine for Unit 3 turbine driven feed water pump A in Zhanjiang Power Plant.

36. It is not very effective to monitor friction between rotor and stationary of a steam turbine by vibration signal indirectly in power station because of the restriction of vibrometer and heavy rotor.

37. Using nonlinear programming theory and computer technique for the steam turbine regenerative system, the problem of the feed-water enthalpy rise optimal distribution is solved.

38. Load dump anticipation(LDA) function are one of the important steps to ensure the success of the steam turbine load dump test, and this circumstance is vary rare.

39. Radial rub is one of the main faults of the steam turbine.

40. The performance of live steam valve for steam turbine is greatly influenced by the profile of valve disc. Three types of elementary valves are designed.

41. In a steam turbine,() steam from pipes is directed onto the blades.

42. Fourier harmonic analysis is applied to analyze the factors that affect steam turbine blade excitation.

43. Dry friction damping, which widely used in blades of aero engine, steam turbine and gas turbine, is an effective and simple measure for vibration reduction of blades.

44. Mathematic model was established through the analysis of the properties of the typical steam turbine lubricating oil system and the base conservation equation.

45. The former afterheat utilizing system generates electricity by burning oil to super-heat saturated steam and drive the steam turbine or depressurizing through a decompressor.

46. DEH is the model form of modern steam turbine control system.

47. The vapor pressure, speed, discharge main valve of steam turbine make direct influence to its operation.

48. So it can raise safety performance and work efficiency of steam turbine system.

49. B3-3.43/0.981 type back-pressure steam turbine in the power station of Nanyang Factory of Paraffin Fine Chemical has troubles of bearing vibration, thrust disc and journal scratch.

50. The fast cooling technology of steam turbine is the process that the cooling medium is used to accelerate the temperature reduction of cylinder and rotor after the shutdown of turbogenerator.

51. Combined with computer simulation, this method can be applied to steam turbine performance prediction, optimizing control as well as condition monitoring and fault diagnosis.

52. Whether application of the power equipment of the steam turbine or steam engine, their basic function principle and apply the same basic cycle.

53. The boiler feed water pump turbine (BFPT) is one of the main products of Hangzhou Steam Turbine Co.

54. Forced air cooling is a reasonable shut-down cooling mode of steam turbine.

55. The paper discusses some problems on small steam turbine generator unit for low vacuum heating.

56. A treatment method of super-saturation steam for deposited salt in steam turbine is introduced, output of the steam turbine is therefore improved through purge.

57. The paper presents a successful try-out of using the boundary element method for the stress analysis of a steam turbine rotor.

58. This paper considers the steam turbine blade group as a rotationally periodic structure and the complex constraint has been induced.

59. Taking a triple pressure reheat HRSG in the gas-steam combined cycle as an example, a general expression of the steam turbine thermal efficiency to coupling parameter with the unfired HRSG is derived.

60. It is found out that the approximate thermodynamic performance of the steam turbine in a combined cycle plant is determinate when the PPTD in HRSG and the parameters of the gas turbine is known.

61. A set consisting of a multi- cylinder steam turbine and a generator in one line of shafting.

62. On - line fault diagnosis for steam turbine rotors is important to the safe operation of power plants.

63. The first steam turbine ship was killed in the cradle.

64. Based on an example, the feed-water enthalpy rise distribution for the domestic 200MW steam turbine regenerative system is discussed in this paper.