1. The cylinder head has been carefully machined to increase air-flow.

2. The engine block and alloy cylinder head is shared with the 1.4-litre Energy engine so the bore is identical.

3. The cylinder head is heavily finned for strength.

4. Place the engine cylinder head over the dowels.

5. The cylinder head gasket is made of solid steel.

6. Clean the exhaust manifold and cylinder head mating surfaces.

7. This is achieved by using cylinder head gasket.

8. Remove control cables from cylinder head cover clip.

9. The powder cylinder head good case of impurities. 3.

10. In this paper, taking example for the diesel cylinder head cover, the low noise design process of parts was expatiated, which MBD, FEM and BEM were combined with topology optimization.

11. The cylinder head is attached to the block with high - tensile steel studs.

12. In this paper, the temperature reduction of cylinder head metal wall and the influence on engine performance are investigated by different thickness of PSZ coating on cylinder head combustion surface.

13. The combustion pressure force in the cylinder head bolts is transferred via reinforced sections in the cylinder block walls direct to the main bearings.

14. The most common cylinder head types are the hemi, wedge, and semi - hemi.

15. The features of cylinder block and cylinder head core assembly vertical casting process are introduced.

16. The engine cylinder head made by vermicular graphite cast iron is not easy to control because of many factors influenced on the production quantity and its optarion limits are very narrow.

16. try its best to gather and create good sentences.

17. A north-west gale had given us a good shaking up crossing from Peterhead to Wick resulting in a cracked cylinder head.

18. It is perfectly possible to replace the hot spots in a Land Rover cylinder head.

19. The only effective remedy is to install hardened valve seats or a replacement cylinder head, both expensive options.

20. The question is the charge of gas, exploded in the cylinder head, which is the motive force of every piston-stroke.

21. The features and principles of the double tightening method for cylinder head bolts is introduced to insure the uniform pressure on cylinder gasket during assembling operation.

22. Research has believed that veining in admission and exhaust passage of diesel engine cylinder head may mainly be caused by crack of sand core occurring in high temperature phase change expansion.

23. A numerical simulation is presented for 3 - D filling progress of engine cylinder head casting.

24. The relationship between calcium stearate and sand core as well as casting quality of cylinder head of diesel engine for example is analyzed.

25. Several important tests on torque - angle tightening process of diesel engine cylinder head bolts were introduced.

26. A fuel injection valve (17) is mounted to an upper surface of the cylinder head (20).

27. Based on the analysis of the data obtained, the inverse filter is designed, and the measurement of the cylinder pressure from the cylinder head acceleration by in...

28. In addition, the influence of different idling speeds, different positions of idling air screw and different temperatures of cylinder head on exhuast emissions is also discussed.

29. Through reliability analysis, F 3 is the best proposal operation requirement of current cylinder head.

30. The conclusions are of benefit to the improvement of the diesel engine with integrated cylinder head.

31. An engine cylinder head gasket leaking between a cylinder and an adjacent water jacket is indicated by coolant foaming or overheating and loss of coolant.

32. The spark plug must form a good seal inside the cylinder head to avoid leakage of without the high-tension current shorting-out.

33. The characters, development and process of Vermicular Graphite Cast Iron (VGCI) were discussed, and then the main reason of diesel locomotive VGCI cylinder head leakage was analyzed.

33. try its best to gather and make good sentences.

34. Install the engine cylinder head, push rods, rocker arms, bridges, pivots and engine cylinder head cover.

35. The cylinder head water jacket of a high speed diesel engine is analyzed by using CFD technology.

36. The results expatiated that the strength of such cylinder head gasket meet the need when being used.

37. The relationship between calcium stearate and sand core as well as casting quality of cylinder head of diesel engine for example ...

38. A bolt is fastened through the bush to thereby fix the rocker shaft on a cylinder head.

39. The cast production technology and its control means of Cumins 6 BT cylinder head production are described.

40. The Breakdown of large complex cylinder head core is close related to the hot strength - Toughness propertiesof precoated phenolic resin sand during the drawing of patterns.

41. We must find out the most important influencing factor of them and control it firstly in order to develop the cylinder head made by vermicular graphite cast iron .

42. The main defect of type YC 4112 Q cylinder head is blowhole.

43. A new lateral casting process was introduced to produce YC 6 M cylinder head.

44. In order to reduce rate of waste products caused by blowhole for CA488 engine aluminum cylinder head casting,() the gas evolution of molding materials was studied.

45. Preload condition, the cylinder head bolt-hole depth of deformation of the cylinder sets a great impact on the proper cylinder head bolt hole depth Shen cylinder l.

46. The basic casting method - design principle of cylinder head was introduced.

47. Allan, a mechanic, was removing a cylinder head from a Harley-Davidson motorbike, when he spotted a world-famous heart surgeon in his garage.

48. Rubber O-ring, Gasket, Rubber Bonding Parts For Car. Cylinder Head Gasket For Truck Engine.

49. Maintenance: Both cylinder bore and cylinder head valve guide tube can be repaired by resisting.

50. The flame barrier, which locates into a groove in the cylinder head, reduces the stresses on the cylinder head gasket.

51. A thermal radiant sensor is designed to measure the radiant heat flux of the cylinder head.