1. Larger more comfortable malleable iron handwheel for easier operation.

2. Remove the access screw; do not remove handwheel.

3. Handwheel adjusting mechanism with digital display, accurate and flexible.

4. Refit the handwheel retaining screw.

5. Reinstall handwheel and secure with retaining bolt.

6. Valves supplied with hammer blow handwheel as a standard.

7. Regulation is accomplished by rotating the handwheel clockwise.

8. Handwheel or handle can not be slung.

9. Cast Steel Valves Hammerblow Handwheel, Seat Rings, Wedges.

10. Actuation – can be supplied with a hammerblow handwheel, manual gear set, electric motor operator, pneumatic Globe valve calss 300Lb or hydraulic cylinder operator.

11. When the handwheel is rotated to the closed position the upper stem pushes on the diaphragms, which deflect downward, forcing the lower stem against the valve seat.

12. Minimum dimension from centerline of valve to handwheel when ordered without floorstand.

13. The extension includes fittings and extension pipe with handwheel mounted.

14. Twist the handwheel baseplate and handwheel grip until the decimal indicator displays 0-0,[ ] then refit the complete handwheel assembly onto the valve stem.

15. Rotate handwheel from full OPEN to full SHUT positions several times to assure proper operation.

16. Remove handwheel and turn indicator sleeve by grasping the handwheel and pulling away from the valve body along the stem.

17. Possible handwheel orientations are shown in the figure to the right below.

18. Single pulling the handwheel through tooth synchronous transmission chain, ensure single-side chuck pull synchronization.

19. Hammerblow handwheel adapters can be furnished with handwheel or chainwheel construction.

20. Valves are supplied with a handwheel actuator on all sizes.

21. Includes floorstand with gate position indicator, handwheel, fittings and extension.

22. The most economical mechanism for tight shutoff is the impactor handwheel.

23. Bevel gear actuators are available on 2 - 48 " ( DN 50 - DN 1200 ) valves with handwheel or actuators. "

24. Stems shall be of dezincification-resistant silicon bronze ASTM B 371 or low-zinc alloy B 99, non-asbestos packing and malleable or ductile iron handwheel.

25. To order, specify description and extension length from center line of valve to handwheel.

26. Gear operated valves shall be equipped with position indicator and high impact polypropylene handwheel.

27. Loosen the scale retaining ring and rotate the turn indicator scale to align with the "0" on the handwheel.

28. This dimension must be at least twice dimension from line to handwheel.

29. Stems shall be of dezincification-resistant silicon bronze ASTM B 371 or low-zinc alloy B 99 non-asbestos packing and malleable or ductile iron handwheel. Valve ends may be threaded or solder type.

30. Bearing very good circuit - adjusting function and accurate controlled value of handwheel.

31. It is the handwheel adjustment of the kerosene stove wick.

32. Specify required extension length from centerline of valve to handwheel.

33. The height between rocker and work table is adjusted by handwheel, which is simple and convenient.

34. FEATURES: adopted cricoid feed foot and driving handwheel . Not wrinkling shen sewing thin materials.

35. Available on all sizes of handwheel and bevel gear handwheel operated valves. To order, add a comma and the order code "LK" after the actuator code.

36. To order handwheel or chainwheel actuators, add the appropriate order code to the basic valve order code.

36.

37. Carefully remove handwheel and turn indicator sleeve assembly, leaving the valve at its balance set point.

38. Actuation – can be supplied with a hammerblow handwheel, manual gear set, electric motor operator, pneumatic or hydraulic cylinder operator.

39. This robust handwheel is used in association with the machine control.

40. Only the handwheel (1), pin (2), and some adapter bushings (4) are available for repair parts.

41. By turning the handwheel counterclockwise, the tool is displaced in a negative direction with respect to the position of the coordinate system.

42. The extension includes fittings and extension pipe with handwheel or nut mounted.