1. Research results: Under the same load condition, the tensile stress of ballastless track slabs without close connected is bigger than that of slabs with close linkage structure.

2. We would like to know the tensile stress in the wall.

3. Tensile stress and compressive stress have different effects on the magnetic domain structure.

4. The new formula for computing the allowable tensile stress given in the new specifications is not reasonable.

5. The specimen deforms under a tensile stress applied parallel to the fibres.

6. But under the control of NE-SW tensile stress field of Early Cretaceous, in the eastern part of "Ergun Block" sag belt was formed and the basement tectonics is NE-NNE direction.

7. These outside conditions include environmental temperature, voltage, tensile stress, and bending load.

8. Figure 4 shows a plot of tensile stress versus distance from the weld for 6061, revealing curves for both T4 and T6 material in both the as-welded (AW) and post-weld-aged (PWA) conditions.

9. Tensile strength corresponds to the maximum tensile stress that may be sustained by a specimen.

10. Can a bending load makes both compressive and tensile stress in a member?

11. Tensile stress was applied to the fiber prepreg to modify the residual stresses in ARALL during curing.

12. Studies of other tubular organs have shown that the major tensile stress during distension is in the circumferential direction.

13. In this study, a simple bending fixture was used to investigate the effects of tensile stress on the growth of NILC.

14. On the basis of distribution of stresses, it can determine that dam radial displacement is a main factor of axial tensile stress and is less important factor of loop tensile stress.

15. This study shows that the formation of antithetic normal fault is controlled by NE WS strike tensile stress and dextral shear stress and the strike is nearly vertical to the tensile stress.

16. True stress and contraction ratio of the minimum section increases as flow tensile stress decreases.

17. The transverse stress of clad material was analyzed with the mixing rule, and the results show that the yield stress, tensile stress and the thickness ratio obey exponent function.

17.

18. Cracking of a metal resulting from the combination of hydrogen and tensile stress.

19. The analysis on fatigue cracks of the outer race of aero-bearing shows that the distribution of residual tensile stress on race surface could reduce its contact fatigue life.

20. The change in length ( lengthening, stretch ) of a material subject to tensile stress.

21. Objective To evaluate the effects of varying load of vastus medialis oblique on the tensile stress at the proximal insertion of patellar tendon.

22. This paper describes the significance and role of the initial test load holding time in the tensile stress relaxation test at room temperature for the pre-stressed rolled steel.

23. There will be a certain thermal stress in the lining during operation, but the stress is not great, being only about one tenth of the allowable tensile stress of the reinforcing bars.

24. After the crack initiating, it propagates along the vertical direction of the tensile stress axial line.

25. From the results of interlocking nails, the nails with larger outer diameter and smaller nail hole have lower maximal tensile stress.

26. The results show that the top of the gable roof endures strongest tensile stress and is relatively vulnerable under effect of strong earthquake.

27. Thellos paper describes the significance and role of the initial test load holding time in the tensile stress relaxation test at room temperature for the pre-stressed rolled steel.

28. Owing to the loss of their adjacent material constraint, the residual stress on the cutting edge of the small test block reduces, even changing from compressive stress to tensile stress.

29. In this text, the authors analyze the relations of the tensile stress under the base with axle weight and base parameters, and consider the characteristics of asphalt base and semi?

30. It is testified that the landfall happens because of the increase in shearing stress and tensile stress.

31. It is also shown that the residual stresses are compressive below the surface and tensile in the center, and the minimum of local residual tensile stress occurs at the midplane of the plate thickness.

32. This process will bring the glass surface compressive stress and the interior tensile stress which can improve the mechanical strength of glass by gemination and result in good thermal stability.

33. The results indicate that the max tensile stress on the pavements appears on top of the U box which is near the loading area, and the max deformation appears on the center of the loading area.

34. Repeated forceful contractions of wrist extensors or forearm supinator result in tensile stress over the lateral epicondyle.

35. CBM sealed condition is bad under neutral plane at axial part where shows tensile stress in syncline structure.